- Power Type:
- After-sales Service Provided:
Free spare parts, Field maintenance and repair service, Video technical support, Online support, Engineers available to service machinery overseas
- Place of Origin:
- Brand Name:
- The cultivated land is deep: 15-30CM:
reverse gear, gap, forward gear
- Output power:
7 HPP / 3600rpm
- Tank capacity:
- Oil capacity:
- Gross net weight:
- package size:
- Supply Ability:
- 100 Set/Sets per Month Agricultural machines parts tiller blade for Italy cultivator
Packaging & Delivery
- Packaging Details
- Export plywood case package Agricultural machines parts tiller blade for Italy cultivator
- China main sea port ( Eg: Qingdao, Shanghai, Guangzhou, Ningbo, Tianjin and so on)
Quantity(Sets) 1 – 1 2 – 5 6 – 10 >10 Est. Time(days) 7 15 25 To be negotiated
Agricultural machines parts tiller blade for Italy cultivator
Introduction ofAgricultural machines parts tiller blade for Italy cultivator
The rotary tiller uses the engine output power to drive the rotary tilling blade, cutting and turning the soil, and throwing the cut soil back into the mud block to further break the soil block. The flat earth supports the surface of the earth. Finish the ploughing and raking at one time.
1 / depth adjustment generally speaking, rotary tiller tillage depth should not be less than 10 cm. The rotary tiller with walking tractor adjusts the depth of cultivated land by changing the height of the tail wheel. When adjusting, turn the adjusting handle. With wheeled tractor matching rotary tiller, ploughing depth by hydraulic system control. Before adjusting the depth of ploughing, adjust the length of the pulling rod on the tractor until the rotary tiller and the drive shaft are basically in the same plane. Then adjust the position limiter on the piston rod of hydraulic cylinder to limit the depth of the rotary tiller. In order to ensure that the depth of rotary tillage on both sides of the two sides is consistent, the distance between the two sides of the blade tip from the ground should be checked. If the distance from the ground is not consistent, the tractor should be adjusted on both sides of the pull rod. Until the distance between the two sides of the rotary knife from the ground is the same. In order to make the drive shaft and the universal joint rotate smoothly, the distance between the two sides of the rotary tiller and the rear wheel is measured with a ruler to determine whether the angle between the drive shaft and the forward direction is the same or not. If the angle is not consistent, adjust the tractor pull rod to make the rotary tiller in the most favorable working condition. Fourth, elevating height and adjusting the upward inclination of the universal joint over 30 degrees will increase the power loss of the universal joint and easily damage the universal joint. For example, when turning the ground, cutting off the power of the rotary tiller and then raising it will affect the efficiency of work. Therefore, it is necessary to lift the rotary tiller in the transmission. However, the elevation must be limited. Generally elevate to the tip of the knife off the ground 15~20cm is good. V. Blade adjustment according to different farming requirements, blade installation methods are three. When the factory is generally installed into the most commonly used staggered mode, or spiral mode. On the same plane, the staggered way is equipped with a left and right curved knife each, and the blade with two outer ends of the knife shaft bends in all directions, so that the soil block is not thrown to both sides, and the land after plowing is flat, which is suitable for raking after ploughing. A blade at both ends of the shaft bends inward, and the middle blade bends outwards, known as outward. After outward tillage, the soil is thrown to both sides, forming a shallow ditch, suitable for strip-breaking operation. The blades bend to the middle of the blade axis, and the ridge is formed in the middle after tillage, which is suitable for cultivation before the furrow, and can also make the unit cross the furrow on the furrow to fill the furrow. Note that when the blade is rearranged, the blade edge should be in the same direction as the axis. Otherwise, rotary tiller in the work will occur jitter, when serious, damage machine parts.
Specifications ofAgricultural machines parts tiller blade for Italy cultivator
170F single cylinder four stroke gasoline engine
7hp / 3600rpm
Gross net weight
Pictures of Agricultural machines parts tiller blade for Italy cultivator
5, Are you manufacturer?
Yes, we are manufacturer with more than 8 years’ experience.
6, Where are you? Can we go to China and visit your factory?
Yes, of course. We are in Henan, China. Welcome to our factory.
7, Do you have manual with the machine?
Yes, of course. It is in English version.
8, Can you offer us the necessary paper to do the customs clearance?
Yes, of course. We will send you the commercial invoice, sales contract, packing list, bill of lading(FOB or CFR, CIF terms), insurance policy (if CIF terms), also CO if you need.